KONFIGURASI IPV6 ROUTING OSPF

Konfigurasi di Router 0 Router>en Router#conf t Enter configuration commands, one per line.  End with CNTL/Z. Router(config)#host wahyu1 wahyu1(config)#ipv6 unicast-routing wahyu1(config)#ipv6 router ospf 10 %OSPFv3-4-NORTRID: OSPFv3 process 10 could not pick a router-id,please configure manually wahyu1(config-rtr)#router-id 1.1.1.1 wahyu1(config-rtr)#auto-cost reference-bandwidth 1000 % OSPF: Reference bandwidth is changed.         Please ensure reference bandwidth is consistent across all routers. wahyu1(config-rtr)#int g0/0 wahyu1(config-if)#bandwidth 1000000 wahyu1(config-if)#ipv6 address 2001:DB8:CAFE:1::/64 wahyu1(config-if)#ipv6 address FE80:1 link-local                                       ^ % Invalid input detected at '^' marker.                 wahyu1(config-if)#ipv6 address FE80::1 link-local wahyu1(config-if)#ipv6 ospf 10 area 0 wahyu1(config-if)#no shut wahyu1(config-if)# %LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up wahyu1(config-if)#ex wahyu1(config)#int se0/0/0 wahyu1(config-if)#ipv6 address 2001:DB8:CAFE:A001::/64 wahyu1(config-if)#ipv6 ospf 10 area 0 wahyu1(config-if)#no shut %LINK-5-CHANGED: Interface Serial0/0/0, changed state to down wahyu1(config-if)#ex wahyu1(config)#int se0/0/1 wahyu1(config-if)#ipv6 address 2001:DB8:CAFE:A003::/64 wahyu1(config-if)#ipv6 ospf 10 area 0 wahyu1(config-if)#no shut %LINK-5-CHANGED: Interface Serial0/0/1, changed state to down wahyu1(config-if)#ex wahyu1(config)# Konfigurasi Router 1 Router>en Router#conf t Enter configuration commands, one per line.  End with CNTL/Z. Router(config)#host wahyu2 wahyu2(config)#ipv6 unicast-routing wahyu2(config)#ipv6 router ospf 10 %OSPFv3-4-NORTRID: OSPFv3 process 10 could not pick a router-id,please configure manually wahyu2(config-rtr)#router-id 2.2.2.2 wahyu2(config-rtr)#auto-cost reference-bandwidth 1000 % OSPF: Reference bandwidth is changed.         Please ensure reference bandwidth is consistent across all routers. wahyu2(config-rtr)#int g0/0 wahyu2(config-if)#bandwidth 1000000 wahyu2(config-if)#ipv6 address 2001:DB8:CAFE:2::/64 wahyu2(config-if)#ipv6 address FE80::2 link-local wahyu2(config-if)#ipv6 ospf 10 area 0 wahyu2(config-if)#no shut wahyu2(config-if)# %LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up wahyu2(config-if)#ex wahyu2(config)#int se0/0/0 wahyu2(config-if)#ipv6 address 2001:DB8:CAFE:A001::/64 wahyu2(config-if)#ipv6 ospf 10 area 0 wahyu2(config-if)#no shut wahyu2(config-if)# %LINK-5-CHANGED: Interface Serial0/0/0, changed state to up wahyu2(config-if)#ex wahyu2(config)#int se0/0/1 wahyu2(config-if)#int se0/0/1 %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed s 00:18:37: %OSPFv3-5-ADJCHG: Process 10, Nbr 1.1.1.1 on Serial0/0/0 from LOADING to FULL, Loading Done wahyu2(config-if)#ipv6 address 2001:DB8:CAFE:A002::/64 wahyu2(config-if)#ipv6 ospf 10 area 0 wahyu2(config-if)#no shut %LINK-5-CHANGED: Interface Serial0/0/1, changed state to down wahyu2(config-if)#ex wahyu2(config)#   Konfigurasi Router 2 Router>en Router#conf t Enter configuration commands, one per line.  End with CNTL/Z. Router(config)#host wahyu3 wahyu3(config)#ipv6 unicast-routing wahyu3(config)#ipv6 router ospf 10 %OSPFv3-4-NORTRID: OSPFv3 process 10 could not pick a router-id,please configure manually wahyu3(config-rtr)#router-id 3.3.3.3 wahyu3(config-rtr)#auto-cost reference-bandwidth 1000 % OSPF: Reference bandwidth is changed.         Please ensure reference bandwidth is consistent across all routers. wahyu3(config-rtr)#int g0/0 wahyu3(config-if)#bandwidth 1000000 wahyu3(config-if)#ipv6 address 2001:DB8:CAFE:3::/64 wahyu3(config-if)#ipv6 address FE80::3 link-local wahyu3(config-if)#ipv6 ospf 10 area 0 wahyu3(config-if)#no shut wahyu3(config-if)# %LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up wahyu3(config-if)#ex wahyu3(config)#int se0/0/0 wahyu3(config-if)#ipv6 address 2001:DB8:CAFE:A002::/64 wahyu3(config-if)#ipv6 ospf 10 area 0 wahyu3(config-if)#no shut wahyu3(config-if)# %LINK-5-CHANGED: Interface Serial0/0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up 00:24:55: %OSPFv3-5-ADJCHG: Process 10, Nbr 2.2.2.2 on Serial0/0/0 from LOADING to FULL, Loading Done wahyu3(config-if)#ex wahyu3(config)#int se0/0/1 wahyu3(config-if)#ipv6 address 2001:DB8:CAFE:A003::/64 wahyu3(config-if)#ipv6 ospf 10 area 0 wahyu3(config-if)#no shut wahyu3(config-if)# %LINK-5-CHANGED: Interface Serial0/0/1, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/1, changed state to up 00:25:36: %OSPFv3-5-ADJCHG: Process 10, Nbr 1.1.1.1 on Serial0/0/1 from LOADING to FULL, Loading Done wahyu3(config-if)#ex wahyu3(config)# Setelah itu konfigurasi  ipv6 di semua komputer caranya seperti di bawah ini.  untuk menampilkan routing ospf ipv6   kalau anda berhasil hasilnya seperti yang dibawah ini. (All is Well)

Share on Facebook

Share on Twitter

Share on Google+

Share on LinkedIn

Subscribe to receive free email updates: